Description
20 hp (15 kW) high performance vector variable frequency drive, three phase 220V, 380V, 460V for selection, RS485 enabled.
Specification:
| Basics | Model | GK3000-4T0150G/ GK3000-2T0150G |
| Capacity | 20 hp (15 kW) | |
| Shipping weight | 8 kg | |
| Dimension | 330*200*200 mm for GK3000-4T0150G/ 530*320*235 for GK3000-2T0150G | |
| I/O Feature | Rated current | 32A at 380V ~ 480V, 60A at 220V ~ 240V |
| Input voltage | 3 phase 220V /380V /460V AC ±15% (Optional) | |
| Input frequency | 50Hz/ 60Hz | |
| Output voltage | 3 phase AC 0~input voltage | |
| Output frequency | 0Hz~1000Hz | |
| Over load capacity | 150% of rated current for 1 minute, 180% of rated current for 3 seconds | |
| Control Feature | Control mode | V/F control; Sensorless vector control; |
| Communication | RS485 | |
| Speed regulation | 1:100 | |
| Start torque | 150% of rating torque at 1 Hz | |
| Speed control accuracy | ≤±0.5% of rating synchronous speed | |
| Frequency precision | Digital setting: max frequency x± 0.01%; Analog setting: max frequency x± 0.2% |
|
| Frequency resolution | Analog setting: 0.1% of max frequency; Digital setting: 0.01Hz |
|
| Torque boost | Automatic torque boost, manual torque boost 0.1%~30.0% | |
| Interior PID controller | Be convenient to make closed-loop system | |
| Automatic energy save running | Optimize V/F curve automatically based on the load to realize power save running | |
| Automatic voltage regulation (AVR) | Can keep constant output voltage when power source voltage varies. | |
| Automatic current limiting | Limit running current automatically to avoid frequent over-current which will cause trip | |
| Environment | Enclosure rating | IP 20 |
| Temperature | –10℃~ +40℃; VFD will be derated if ambient temperature exceed 40℃; each rise 1℃, the derate will be 5% | |
| Humidity | 5%-95%, without condensation | |
| Altitude | ≤1000m; VFD will be derated if above 1000m | |
| Impingement and oscillation | Normal running:<5.9m/s2 (0.6g); Transportation:<15m/s2 (1.5g) | |
| Store environment | –20℃~ +60℃; no dust, no corrosive gas, no direct sunlight |
Note: ATO VFD Cannot be used as a power source, it Can only be directly connected to an induction motor to control the motor speed.
Tips: Variable frequency drive selection precautions
- The purpose of using VFD: Constant voltage control, constant current control or others.
- The load type of the VFD: Such as vane pump, displacement pump or others, pay special attention to the load performance curve, the performance curve determines the applications method.
- The VFD and the load matching problem:
1) Voltage matching: The rated voltage of VFD should be accordance with the rated voltage of the load.
2) Current matching: For ordinary centrifugal pump, VFD rated current and motor rated current should be accordant. For special loads such as deep water pumps, should refer to the motor performance parameters, use the maximum current to determine the VFD current and overload capacity.
3) Torque matching: This situation may occur when a constant torque load or a deceleration device is present. - When using VFD to drive high-speed motor, due to high-speed motor reactance is small, higher harmonics increase may cause output current value increases. So for high-speed motor, the capacity of VFD should be slightly higher than for ordinary motor.
- If the VFD will use long cable, should take measures to suppress effect from the long cable to the ground coupling capacitor, in order to avoid insufficient output of the VFD. So in this case, should choose a VFD with higher capacity or install a reactor on the output terminal.
- For some special applications, such as high temperature or high altitude, these situations will cause the VFD derating capacity, and should choose a higher capacity VFD.
Reviews
There are no reviews yet.